Sherex Fastening Solutions, LLC - Disc-Lock® Stainless Steel Washers

Features & Benefits

Heavy-duty, self-locking design
For use with bolts up to Class 10.9, Grade 8
Available in sizes from 1/4" (M6) to 1-1/2" (38MM) Other sizes available by special order.
Available in 316L Stainless Steel
Carbon Steel washers are case hardened and coated with RoHS-compliant Delta Protekt®
Provided in pre-assembled, glued pairs
Easy to install with standard tools
No re-tightening needed once installed
Vibration proof according to MIL-STD-1312-7

Proven Results
Disc-Lock® Locking Washer Junker Test

Disc-Lock® Wedge Locking Washers have been tested on a Junker Vibration Machine. The Junker test, considered the most severe vibration test for bolted joints according to DIN 65151, is used to determine the point at which a bolted joint loses its preload when subjected to shear loading due to transverse vibration.

When tested against a standard washer using the Junker test, Disc-Lock® Wedge Locking Washers remained secure under severe vibration conditions, while the standard washer loosened significantly.

Proven Applications
Disc-Lock® Wedge Locking Washers outperform conventional, split-ring, and other style washers in a wide variety of high stress, corrosive, and vibration-sensitive applications including:

Agriculture Equipment
Automotive
Construction Equipment
Heavy Rail
Logging Equipment
Marine
Military
Mining
Oil Drilling Equipment
Solar
Wind
Waste Management

Installation

To install the Disc-Lock® Washer, place the preassembled pair of washers between the nut and the joint material.
As the nut is tightened, one half of the Disc-Lock® Washer is seated to the joint material and the other to the nut.
Disc-Lock® Washers should only be used against flat, relatively smooth metal surfaces.
If the joint material is not metal, the Disc-Lock® washer may be used by securing the metal plate to the joint material in such a manner that the metal plate will not rotate.
A torque wrench is not required to install Disc-Lock® Washers.
An air-gun can be used when installing and removing Disc-Lock® Washers.
If installed correctly, the Disc-Lock® Washer will ensure that the fastener remains secure, and will not require any re-tightening.

Torque Guidelines
When installing Disc-Lock® Washers in a common application, expect an increase in required torque over recommended installation torque to achieve proper clamp load and maximum joint safety. Due to varying installation conditions and customer-specific applications, additional information and torque recommendations are available by contacting Engineering support at Disc-Lock®.

Note
Disc-Lock® Wedge Locking Washers are also available through our Made in the U.S.A. product line.

Unit of Measure

Items	DL-M6-1/4ss Disc-Lock™ 0.262 Inch (in) Inner Diameter Stainless Steel Washer	DL-M8-5/16ss Disc-Lock™ 0.326 Inch (in) Inner Diameter Stainless Steel Washer	DL-M10-3/8ss Disc-Lock™ 0.409 Inch (in) Inner Diameter Stainless Steel Washer	DL-M11-7/16ss Disc-Lock™ 0.450 Inch (in) Inner Diameter Stainless Steel Washer	DL-M12-1/2ss Disc-Lock™ 0.510 Inch (in) Inner Diameter Stainless Steel Washer
Description	N/A Features & Benefits Heavy-duty, self-locking design For use with bolts up to Class 10.9, Grade 8 Available in sizes from 1/4" (M6) to 1-1/2" (38MM) Other sizes available by special order. Available in 316L Stainless Steel Carbon Steel washers are case hardened and coated with RoHS-compliant Delta Protekt® Provided in pre-assembled, glued pairs Easy to install with standard tools No re-tightening needed once installed Vibration proof according to MIL-STD-1312-7 Proven Results Disc-Lock® Locking Washer Junker Test Disc-Lock® Wedge Locking Washers have been tested on a Junker Vibration Machine. The Junker test, considered the most severe vibration test for bolted joints according to DIN 65151, is used to determine the point at which a bolted joint loses its preload when subjected to shear loading due to transverse vibration. When tested against a standard washer using the Junker test, Disc-Lock® Wedge Locking Washers remained secure under severe vibration conditions, while the standard washer loosened significantly. Proven Applications Disc-Lock® Wedge Locking Washers outperform conventional, split-ring, and other style washers in a wide variety of high stress, corrosive, and vibration-sensitive applications including: Agriculture Equipment Automotive Construction Equipment Heavy Rail Logging Equipment Marine Military Mining Oil Drilling Equipment Solar Wind Waste Management Installation To install the Disc-Lock® Washer, place the preassembled pair of washers between the nut and the joint material. As the nut is tightened, one half of the Disc-Lock® Washer is seated to the joint material and the other to the nut. Disc-Lock® Washers should only be used against flat, relatively smooth metal surfaces. If the joint material is not metal, the Disc-Lock® washer may be used by securing the metal plate to the joint material in such a manner that the metal plate will not rotate. A torque wrench is not required to install Disc-Lock® Washers. An air-gun can be used when installing and removing Disc-Lock® Washers. If installed correctly, the Disc-Lock® Washer will ensure that the fastener remains secure, and will not require any re-tightening. Torque Guidelines When installing Disc-Lock® Washers in a common application, expect an increase in required torque over recommended installation torque to achieve proper clamp load and maximum joint safety. Due to varying installation conditions and customer-specific applications, additional information and torque recommendations are available by contacting Engineering support at Disc-Lock®. Note Disc-Lock® Wedge Locking Washers are also available through our Made in the U.S.A. product line.
Dimensions	N/A
Brands	N/A Disc-Lock™
Size	N/A 1/4 in6	N/A 5/16 in8	N/A 3/8 in10	N/A 7/16 in11	N/A 1/2 in12
Inner Diameter (A)	N/A 0.262 in6.66 mm	N/A 0.326 in8.28 mm	N/A 0.409 in10.38 mm	N/A 0.45 in11.43 mm	N/A 0.51 in12.95 mm
Outer Diameter (C)	N/A 0.495 in12.57 mm	N/A 0.628 in15.95 mm	N/A 0.705 in17.90 mm	N/A 0.880 in22.35 mm	N/A 0.937 in23.82 mm
Thickness (EE)	N/A 0.101 in2.560 mm	N/A 0.119 in3.020 mm	N/A 0.135 in3.4 mm	N/A 0.135 in3.330 mm	N/A 0.136 in3.450 mm
Box Quantity	N/A 3,000	N/A 3,000	N/A 1,000	N/A 1,000	N/A 1,000
Material	N/A 316L Stainless Steel
Industry Standards/Compliance	N/A ISO 9001:2008 ISO TS16949 MIL-STD-1312-7 RoHS
Package Type	N/A Box
Features and Benefits	N/A Heavy-duty, self-locking design For use with bolts up to Class 10.9, Grade 8 Available in sizes from 1/4" (M6) to 1-1/2" (38MM) Other sizes available by special order. Available in 316L Stainless Steel Carbon Steel washers are case hardened and coated with RoHS-compliant Delta Protekt™ Provided in pre-assembled, glued pairs Easy to install with standard tools No re-tightening needed once installed Vibration proof according to MIL-STD-1312-7
Proven Results	N/A Disc-Lock™ Locking Washer Junker Test Disc-Lock™ Wedge Locking Washers have been tested on a Junker Vibration Machine. The Junker test, considered the most severe vibration test for bolted joints according to DIN 65151, is used to determine the point at which a bolted joint loses its preload when subjected to shear loading due to transverse vibration. When tested against a standard washer using the Junker test, Disc-Lock™ Wedge Locking Washers remained secure under severe vibration conditions, while the standard washer loosened significantly.
Proven Applications	N/A Disc-Lock™ Wedge Locking Washers outperform conventional, split-ring, and other style washers in a wide variety of high stress, corrosive, and vibration-sensitive applications including: Agriculture Equipment Automotive Construction Equipment Heavy Rail Logging Equipment Marine Military Mining Oil Drilling Equipment Solar Wind Waste Management
Installation	N/A To install the Disc-Lock™ Washer, place the preassembled pair of washers between the nut and the joint material. As the nut is tightened, one half of the Disc-Lock™ Washer is seated to the joint material and the other to the nut. Disc-Lock™ Washers should only be used against flat, relatively smooth metal surfaces. If the joint material is not metal, the Disc-Lock™ washer may be used by securing the metal plate to the joint material in such a manner that the metal plate will not rotate. A torque wrench is not required to install Disc-Lock™ Washers. An air-gun can be used when installing and removing Disc-Lock™ Washers. If installed correctly, the Disc-Lock™ Washer will ensure that the fastener remains secure, and will not require any re-tightening.
Torque Guidelines	N/A When installing Disc-Lock™ Washers in a common application, expect an increase in required torque over recommended installation torque to achieve proper clamp load and maximum joint safety. Due to varying installation conditions and customer specific applications, additional information and torque recommendations are available by contacting Engineering support at Disc-Lock™.
Note	N/A Disc-Lock Wedge Locking Washers are also available through our Made in the U.S.A. product line.
Resources	N/A Disc Lock Washer Catalog